Publications

Publications of Stephen J. Lombardo

  1. “High Temperature Chemistry During the Sintering of Strontium Titanate,” (M. Schurwanz, J. W. Yun, C. S. Kim, and S. J. Lombardo) submitted to the Journal of the American Ceramic Society (2011).
  2. “Fabrication and Electrical Properties of Polymer-Derived Ceramic (PDC) Thin Films for High-Temperature Heat Flux Sensors,” (D. Seo, S. Jung, S. J. Lombardo, Z. C. Feng, J. K.Chen, and Y. Zhang) accepted to Sensors and Actuators A: Physical (2011).
  3. “Effect of a Combined Supercritical Extraction/Thermal Cycle on Binder Removal Cycle Time, Yield, and Residual Carbon of Multilayer Ceramic Capacitors,” (B. Abeln and S.J. Lombardo) submitted to Journal of Ceramic Processing Research (2011).
  4. Effect of Green Body Size and Heating Rate on Failure during Thermal Debinding and on Debinding Cycle Time,” (R. M. Sachanandani and S. J. Lombardo) accepted to Journal of Ceramic Processing Research (2011).
  5. Modeling of Green Body Strength, Internal Pressure, and Stress in Porous Ceramic Bodies During Thermal Debinding” (R. Sachanandani and S. J. Lombardo) accepted to Journal of Ceramic Processing Research (2011).
  6. “Development of a Heating Schedule for Rapid Thermal Debinding of Green Multilayer Ceramic Capacitors,” (K Krishnamurthy and S. J. Lombardo) Journal of Ceramic Processing Research 11 (2010) 405-410.
  7. “Teaching Technical Writing in a Lab Course in ChE,” (S. J. Lombardo) Chemical Engineering Education (2010) 58-62.
  8. “Effect of Lamination on the Adhesion Strength, Gas Permeability, and Yield During Binder Removal of Green Ceramic Tapes,” (J. W. Yun, P. J. Scheuer, D. S. Krueger, and S. J. Lombardo) Advances in Applied Ceramics 108 (2009) 488-493.
  9. “Pressure Distribution and Defect Formation in Green Ceramic Bodies During Supercritical Extraction of Binder,” (K. Krishnamurthy and S. J. Lombardo), Journal of the American Ceramic Society 92 (2009) 365-370.
  10. “Determination of Rapid Heating Cycles for Binder Removal from Open-Pore Green Ceramic Components,” (J. W. Yun and S. J. Lombardo) Advances in Applied Ceramics 109 (2009) 92-101.
  11. “Scaling Analysis of the Effect of Binder Content and Binder Distribution on the Gas Permeability of Porous Green Ceramics,” (J. W. Yun and S. J. Lombardo) Journal of the American Ceramic Society 91 (2008) 2150-2155.
  12. “Effect of Lamination Conditions on the Gas Permeability and Adhesion Strength of Green Ceramic Tapes,” (J. W. Yun, P. J. Scheuer, D. S. Krueger, and S. J. Lombardo) Advances in Applied Ceramics 107 (2008) 190-198.
  13. “Curvature and Bifurcation of MgO-Al2O3 Bilayer Ceramic Structures,” (C. S. Kim and S. J. Lombardo) Journal of Ceramic Processing Research 9 (2008) 93-96.
  14. “Permeability of Laminated Green Ceramic Tapes as a Function of Binder Loading,” (J. W. Yun and S. J. Lombardo) Journal of the American Ceramic Society 91 (2008) 1553-1558.
  15. “Methods for Introducing Safety Factors into Minimum Time Heating Cycles for Binder Removal from Green Ceramic Bodies,” (J. W. Yun and S. J. Lombardo), Journal of Ceramic Processing Research 8 (2007) 402-410.
  16. “The Effect of Processing Conditions and Porosity on the Electrical Properties of Y2O3-doped SrTiO3 Internal Boundary Layer Capacitors,” (D. S. Krueger and S. J. Lombardo), Journal of Ceramic Processing Research 8 (2007) 31-37.
  17. “Permeability of Green Ceramic Tapes as a Function of Binder Loading,” (J. W. Yun and S. J. Lombardo) Journal of the American Ceramic Society 90 (2007) 456-461.
  18. “Effect of Processing on the Microstructure and Deformation of MgO-Al2O3, CaO-Al2O3, and SiO2-Al2O3 Layered Composites,” (C. S. Kim and S. J. Lombardo) Journal of Ceramic Processing Research 8 (2007) 43-51.
  19. “Effect of Processing on the Microstructure and Induced Strain Mismatch in Magnesia-Alumina Layered Composites,” (C. S. Kim, R. A. Winholtz, and S.J. Lombardo), Journal of the American Ceramic Society 89 (2006) 2718-2725.
  20. “Heat Transfer Effects in Porous Green Bodies During Binder Removal by Minimum Time Heating Cycles,” (J. W. Yun and S. J. Lombardo), Journal of the American Ceramic Society 89 (2006) 1193-1199.
  21. “Effect of Decomposition Kinetics and Failure Criteria on Binder Removal Cycles From Three-Dimensional Porous Green Bodies,” (J. W. Yun, D. S. Krueger, P. Scheuer, and S. J. Lombardo) Journal of the American Ceramic Society 89 (2006) 176-183.
  22. “Adsorption and Diffusion Behavior of Ethane and Ethylene in Sol-Gel Derived Microporous Silica,” (A. C. DeWitt, K. W. Herwig, and S. J. Lombardo) Adsorption 11 (2005) 491-499.
  23. “Ceramics,” S. J. Lombardo, invited entry, Encyclopedia of Chemical Processing, Vol. 1, ed. S. Lee, (Marcel Dekker/Taylor & Francis, NY, 2005) 417-428.
  24. “Strain Induced Deformation in Alumina-Magnesia Layered Composites,” (C. S. Kim, R. A. Winholtz, and S. J. Lombardo) Journal of the American Ceramic Society 88 (2005) 2064-2070.
  25. “A Visual Rankine Cycle Simulation Using Labview,” (P. A. Tebbe, S. J. Lombardo, W. Miller, C. Weisbrook) Computers in Education 14 (2004) 90-96.
  26. “Using Small Blocks of Time for Active Learning and Critical Thinking in the Chemical Engineering Curriculum,” (S. J. Lombardo) Chemical Engineering Education 38 (2004) 150-153.
  27. “Defect Formation during Supercritical Extraction of Binder from Green Ceramic Components, (R. V. Shende, T. R. Redfearn, and S. J. Lombardo) Journal of the American Ceramic Society 87 (2004) 1254-1258.
  28. “Effect of Porosity on the Electrical Properties of Y2O3-doped SrTiO3 Internal Boundary Layer Capacitors,” (D. S. Krueger, R. V. Shende, and S. J. Lombardo), Journal of Applied Physics 95 (2004) 4310-4315.
  29. “Effects of Supercritical Extraction on the Plasticization of Poly(vinyl butyral) and Dioctyl Phthalate Films,” (R. V. Shende, M. Kline, and S. J. Lombardo) Journal of Supercritical 28 Fluids (2004) 113-120.
  30. “Solid State Synthesis, Processing, and Electrical Properties of Sr(TixZr1-x)O3 (0£x£1) Ceramics for High Voltage Applications,” (R. V. Shende, D. S. Krueger, and S. J. Lombardo) Journal of Ceramic Processing Research 4 (2003) 191-196.
  31.  “Determination of the Minimum Time for Binder Removal and Optimum Geometry for Three-Dimensional Porous Green Bodies,” (S. J. Lombardo and Z. C. Feng) Journal of the American Ceramic Society 86 (2003) 2087-2092.
  32. “Analytic Method for the Minimum Time for Binder Removal from Three-Dimensional Porous Green Bodies,” (S. J. Lombardo and Z. C. Feng) Journal of Materials Research 18 (2003) 2717-2723.
  33. “Modeling of the Pressure Distribution in Three-Dimensional Porous Green Bodies during Binder Removal,” (K. Feng and S. J. Lombardo) Journal of the American Ceramic Society 86 (2003) 234-240.
  34. “Kinetic Analysis from Dilatometry and Mass Spectrometry Measurementsof the Decomposition and Sintering of Calcium Carbonate,” (K. Feng and S. J. Lombardo) Journal of Ceramic Processing Research 3 (2002) 101-108.
  35. “The Effect of Plaster Composition and Binder Concentration on Strain Mismatch and Deformation of Slip-Cast Green Bodies,” (J. D. Yates and S. J. Lombardo) Materials Science and Engineering: A 337 (2002) 297-305.
  36. “High-Temperature Reaction Networks in Graphite Furnaces,” (K. Feng and S. J. Lombardo) Journal of Materials Science 37 (2002) 2747-2753.
  37. “Pressure Distribution during Binder Burnout in Three-Dimensional Porous Ceramic Bodies with Anisotropic Permeability,” (S. J. Lombardo and Z. C. Feng) Journal of Materials Research 17 (2002) 1434-1440.
  38. “Supercritical Extraction with Carbon Dioxide and Ethylene of Poly(vinyl butyral) and Dioctyl Phthalate from Multilayer Ceramic Capacitors,” (R. V. Shende and S. J. Lombardo) Journal of Supercritical Fluids 23 (2002) 153-162.
  39. “Stress Distribution in Porous Ceramic Bodies During Binder Burnout,” (Z. C. Feng, B. He, and S. J. Lombardo) Journal of Applied Mechanics 69 (2002) 497-501.
  40. “Determination of Binder Decomposition Kinetics for Specifying Heating Parameters in Binder Burnout Cycles,” (R. V. Shende and S. J. Lombardo) Journal of the American Ceramic Society 85 (2002) 780-786.
  41. “Supercritical Extraction of Binder Containing Poly(vinyl butyral) and Dioctyl Phthalate from Barium Titanate-Platinum Multilayer Ceramic Capacitors,”  (R. V. Shende, D. S. Krueger, and S. J. Lombardo) Journal of Materials Science: Materials in Electronics 12 (2001) 637-643.
  42. “Strontium Zirconate and Strontium Titanate Ceramics for High-Voltage Applications: Synthesis, Processing, and Dielectric Properties,” (R. V. Shende, D. S. Krueger, G. A. Rossetti, Jr., and S. J. Lombardo) Journal of the American Ceramic Society 84 (2001) 1648-1650.
  43. “Effect of Solids Loading and Dispersant Concentration on Strain Mismatch and Deformation of Slip-Cast Green Bodies,” (J. D. Yates and S. J. Lombardo) Journal of the American Ceramic Society 84 (2001) 2274-2280.
  44. “Optimization of Multi-Layer Ceramic Capacitor Geometry for Maximum Yield during Binder Burnout,” (B. Peters and S. J. Lombardo) Journal of Materials Science: Materials in Electronics 12 (2001) 403-409.
  45. “Role of Length Scale on Pressure Increase and Yield of Poly(vinyl butyral)-Barium Titanate-Platinum Multilayer Ceramic Capacitors During Binder Burnout,” (L. C.-K. Liau, B. Peters, D. S. Krueger, A. Gordon, D. S. Viswanath, and S. J. Lombardo) Journal of the American Ceramic Society 83 (2000) 2645-2653.
  46. “An ‘Open-Ended Estimation’ Design Problem for Thermodynamics Students,” (S. J. Lombardo) Chemical Engineering Education 34 (2000) 154-157.
  47. Forming of Ceramics during Firing without the Application of External Pressure,” (S. J. Lombardo, D. Bianchi, B. Bishop, A. Giannakopoulos, R. Goldsmith, R. Higgins, R. Pober, S. Suresh) Journal of the American Ceramic Society 82 (1999) 1401.
  48. “The Role of Thermal and Transport Properties on the Binder Burnout of Injection-Molded Ceramic Components,” (A. C. West and S. J. Lombardo) Chemical Engineering Journal 71 (1998) 243-252.
  49. “Simulations of the NO+NH3 and NO+H2 Reactions on Pt(100): Steady State and Oscillatory Kinetics,” (S. J. Lombardo, T. Fink, and R. Imbihl) Journal of Chemical Physics 98 (1993) 5526-5539.
  50. “The NO+NH3 Reaction on Pt(100): Steady State and Oscillatory Kinetics”, (S. J. Lombardo, F. Esch, and R. Imbihl) Surface Science Letters 271 (1992) L367-L372.
  51. “The NO+H2 and NO+NH3 Reactions on Pt(100): Steady State and Oscillatory Kinetics,” (S. J. Lombardo, M. Slinko, T. Fink, T. Löher, H. H. Madden, F. Esch, and R. Imbihl) Surface Science 269/270 (1992) 481-487.
  52. “Raman Spectroscopy and Thermal Desorption of Ammonia on Titania (Anastase)-Supported Vanadia,” (G. T. Went, L.-J. Leu, S. J. Lombardo, and A. T. Bell) Journal of Physical Chemistry 96 (1992) 2235-2241.
  53. “The NO+H2 Reaction on Pt(100): Steady State and Oscillatory Kinetics,” (M. Slinko, T. Fink, T. Löher, H. H. Madden, S. J. Lombardo, R. Imbihl, and G. Ertl) Surface Science 264 (1992) 157-170.
  54. “A Review of Theoretical Models of Adsorption, Diffusion, Desorption, and Reaction of Gases on Metal Surfaces,” (S. J. Lombardo and A. T. Bell) Surface Science Reports 13 (1991) 1-72.
  55. “Monte Carlo Simulations of the Effect of Pressure on Isothermal and Temperature-Programmed Desorption Kinetics,” (S. J. Lombardo and A. T. Bell) Surface Science 245 (1991) 213-224.
  56. “Monte Carlo Simulation of Temperature-Programmed Desorption of Coadsorbed Species,” (S. J. Lombardo and A. T. Bell) Surface Science 224 (1989) 451-475.
  57. “A Monte Carlo Model for the Simulation of Temperature-Programmed Desorption Spectra,” (S. J. Lombardo and A. T. Bell) Surface Science 206 (1988) 101-123.
  58. “Monte Carlo Simulations of Temperature Programmed and Isothermal Desorption from Single Crystal Surfaces,” (S. J. Lombardo) Ph. D. Thesis, University of California, Berkeley, (1990) 1-.